Changzhou Hengheng Electronic Instrument Co., Ltd. welcome you!
QR code
QR code
0519-83263587

NEWS

NEWS CENTER

WEBSITE ANNOUNCEMENT:Changzhou Hengzheng Electronic Instrument Co., Ltd. welcome you! YOUR CURRENT LOCATION:首页 > News > company news > 正文BACK

Dial viscometer Notes on installing and unloading the rotor

Update time:2017-04-20 10:31:02The number of clicks:3788TimesSize:T|T
The operator must be careful when installing or unloading the rotor. All viscometers can measure extremely small torques due to the rotation of the rotor within the sample fluid. This requires that the friction inside the instrument be kept at a minimum.
The operator must be careful when installing or unloading the rotor. All viscometers can measure extremely small torques due to the rotation of the rotor within the sample fluid. This requires that the friction inside the instrument be kept at a minimum. The instrument is supported by a pivot system and a gemstone bearing system, with almost no friction, as shown on the right. The support mechanism is in the pivot cup just above the position where the rotor is installed.

When the rotor is installed or unloaded, any downward force or lateral movement will cause great wear to the support system.
When you tighten or loosen the rotor, the correct way to install and unload the rotor is to gently lift the nut at the rotor and then lift it firmly. Also remember that the rotor is fixed from the opposite direction of the thread (left hand).
Similar to the precautions described above can ensure that your viscometer or rheometer can provide reliable service for a long time.
Vibration check, there is a quick check to determine the pivot point of your instrument and the status of the gem support system, you can follow the following steps:
1, do not install the rotor in the case, to ensure that the instrument zero scale in the reading window.
2, observe the red pointer just stopped at the zero indicator line.
3. Lift the nut at the rotor and rotate until the indicator reaches + 20%.
4, put down the nut at the rotor and let go, observe the red pointer until the vibration stops. Record the approximate number of vibrations and the time of vibration.
5, red pointer at this time should still stop at the zero indicator line mark. If not stopped at zero, indicating that the instrument's support system has been a certain damage. Continue to repeat the calibration procedure, if the calibration check falls outside the allowable range, call the local office or call the manufacturer directly to tell you the results and get the service for your instrument.
(Edit:HengZheng)
0 Comments
Do not want to log in? click the Publish button to leave a comment as a visitor.

NEWS RECOMMENDATION

What is weight loss?

What is weight loss? There are many customers in the consul...

According to its display and ...

Moisture detector based on the principle of drying directly to ...

"One way along the way" pla...

From October 26 to 29, the Fifth Plenary Session of the 18...

An Overview of the Instrum...

At present, China's instrumentation industry is in high-speed...

FA / JA series of electron...

Place the balance on a stable, vibration-free workbench, as fa...

Electronic balance and classi...

Ultramicro electronic balance: the maximum weighing of the...

Viscometer in the use of the...

Rotational viscometer is widely used in the determination of...

CONTACT US

Address: Changzhou City, Jiangsu Province, Zhongshan City, Long Road 2188, the new gate of Science and Technology ParkContact: Miss Miss
Post Code: 213000
Tel: 0519-83263587
Fax: 0519-83268313
Website: http://www.czhz17.com

CONTACT US
Address: Experimental Building, No. 489, Xinye Road, Xinzhu, Changzhou, Jiangsu, China
Contact: Miss Miss
Post Code: 213000
Tel: 0519-83263587
Fax: 0519-83268313
ATTENTION HENGZHENG
Copyright © 2017 - 2024 Changzhou Hengzheng Electronic Instrument Co., Ltd. All Rights Reserved ICP17024635 Technical support: Ranran technology [Backstage management]